Update do Firmware do sistema de navegação c/PRESPECTIVA 3D

[jcarlos]

como fazer a actualização :

Turn ignition to position 1 (terminal R). 1.
Do not cycle the key or perform diagnosis while installing the new software. Make sure that the power supply is
stable, i.e. do not switch on any electrical loads.
Activate "GPS-Navigation" and acknowledge the screen disclaimer by pushing the rotary knob. 2.
Remove the map CD from the Navigation computer by pressing "eject" button. 3.
Insert the Navigation Software CD (V17.1 P/N 01 59 9 789 299 index "x" for MK III without split
screen, V27 P/N 01 59 0 141 891 index "s" for all other versions).
4.
Mark I System (up to 9/97 production): 5.
After a few seconds, the BMW roundel will appear on the board monitor and will be "filled in" clockwise to
show the progress of loading (approx. 4-6 minutes).
Mark II System (from 9/97 production),
Mark III System (E46 from 06/00 and E38/E39/E52 from 09/00 production),
DVD navigation system (E46, E39, E52 from 09/02 and E53, E85 from 10/02 production):
After a few seconds, a menu of notes on loading procedure and "progress" bar appear on the board monitor.
When the loading process has been completed, the message "Software has been successfully loaded" is displayed.

Remove the operating software CD and confirm the end of the loading process by pressing the rotary
push-button on the board monitor. "OK" appears in the display.
6.
Drive the vehicle before delivering to the customer to ensure the correct function and displaying (Interstate
Icons) of the Navigation system.
7.
LOADING SOFTWARE (E65/E66 ONLY)
When programming any E65/E66 using Progman V21 or higher, you will be prompted by the Progman
screen that "BMW Navigation CD Version 27" must be loaded prior to programming the vehicle.
Note: Connect an approved battery charger before loading software.
Turn on ignition to Terminal R or 15 1.
Enter the Navigation Menu. 2.
Remove the NAVTEQ road map CD/DVD 3.
Insert the Navigation Operating Software CD V27 (P/N 01 59 0 141 891 index "s") into the
navigation computer and use Progman V21 or a more recent version for NAVI03 (DVD navigation).
4.
Select "Yes" with the Controller to install software. 5.
The software will then load in two steps, takes approximately 10-15 minutes. 6.
Do not touch the iDrive while the software is loading. 7.
When the installation is finished the CD will be ejected. The message "Installation Successful, Remove
Software loading CD and press OK" will appear. At this point select "OK" with the Controller.
8.
The Navigation system will then "reinitialize". 9.
When prompted, insert NAVTEQ road map CD/DVD. 10.
Refer to SI B09 05 01 (Coding, Individualization and Programming) for any necessary coding and
programming. Note that Progman will automatically reprogram all programmable control units that do not
have the latest software.
11.
Drive the vehicle before delivering to the customer to approve the correct function and displaying
(Interstate Icons) of the Navigation system.
12.
NAVIGATION COMPUTER REPLACEMENT MK III
When replacing a defective MK III computer, a configuration signal is required to allow the new computer
to load the correct software for its respective application. This is generated by using DIS coding program
"Coding ZCS C45.0" or higher and Navigation System operating software CD V 17.1 or V27.
Connect DIS/GT1 tester to vehicle 1.
From the DIS Coding/Programming select "1 ZCS Coding" 2.
Select appropriate engineering series (E38, E39, etc.) 3.
Select "4 conversion" 4.
Select "3 IKE/Kombi" 5.

Select "2 Language" 6.
At prompt "Is the CD-ROM present?" – select "Yes", but do not insert Navigation CD into the Nav
Computer yet!
7.
First select the main language and then an additional language (the choices are: English, French, Italian,
Spanish, German)
8.
NOTE: The announcer's voice gender (male or female) can't be selected anymore. 9.
MK I, MK II & MK III: Only male.
MK IV (DVD NAV), NAVI01, NAVI02 & NAVI03: Only female
After activation of the automatic coding, the DIS tester tells you to follow the instructions on the monitor
for Navigation CD installation
10.
Place the Navigation CD into the navigation computer CD drive 11.
Important: Do not switch ignition OFF during software loading procedure
Once loading has been completed, remove the CD and then confirm completion by pressing the rotary
push-button on the monitor
12.
Turn ignition OFF for 10 seconds, then turn it ON and conduct a functional check 13.
After this step has been finished, encode the Navigation computer in the regular manner using the path "1
Recoding"
14.
Troubleshooting Hints
The following problems may occur during the software loading procedure:
The message "CD defective" appears on the display screen.
The message "Fault during programming" appears on the display screen.
The message "The system is restarting" appears on the display screen.
The installation process has stopped and the display screen is blank and the power LED on the navigation
computer is off. The CD will not eject.
These complaints are usually the result of a faulty Navigation Operating software CD.
For points 1-3 for error messages that appear on the display screen, check for the correct software version
and try loading a new Navigation CD.
For a CD that will not eject from the Navigation computer follow the procedure below:
Remove the Navigation computer. 1.
Unplug the voltage supply (blue connector). 2.
Reconnect the voltage supply and immediately press the eject button repeatedly until the CD in the
drive is ejected.
3.

Insert a new Navigation CD and restart the installation process. 4.
PARTS INFORMATION
Part Number Description
01 59 9 789 299 Navigation Software CD V17.1 Index "x"
01 59 0 141 891 Navigation Software CD V27 Index "s"
Copies of the CD V27 will be shipped to every BMW Center through the Automatic Tool Shipment
Program.
WARRANTY INFORMATION
Updating the vehicle at customer request is not covered under warranty.
[ Copyright © 2006 BMW of North America, LLC ]

[jcarlos]

JA ALGUEM TEM A VERSAO DOS MAPAS

EM CD PT/ES 2006-2

EM DVD EUROPA 2006-2

obg

[320dM]

eu não tenho duvidas quanto ao que tenho instalado no carro, até fui eu que adquiri os componentes e os instalei mas de qualquer modo indica 3-1/63, ou seja, MkIII Cd, cor, splitscreen
e o software v27 disse que já estava actualizado
não sei o que se passa
esse texto que enviaste li-o ainda há pouco tempo
cumprimentos

[jcarlos]

boletim completo OFICIAL BMW

SI B 84 01 02
Phone, Navigation Systems
March 2006
Technical Service
This Service Information Bulletin supersedes S.I. B84 01 02 dated September 2005.
designates changes to this revision
SUBJECT
Navigation System Operating Software
MODEL
E38 (7 Series)
E39 (5 Series)
E46 (3 Series)
E53 (X5)
E83 (X3)
E85 (Z4)
E65/E66 (7 Series)
SITUATION
With the introduction of navigation system operating software V27, there are currently 2 valid versions of
navigation software.
Navigation system operating software V17.1 is used on MK III systems without "Split Screen". 1.
Navigation system operating software V27 is used on MK I, MK II, all other MK III navigation systems,
MK IV DVD navigation systems on I-Bus vehicles, NAVI01, NAVI02 and NAVI03.
2.
CORRECTION
Navigation system operating software should be updated under the following circumstances:
The Navigation computer has been replaced.
Progman prompts during programming/coding the navigation software to be updated.
If instructed by a Service Information Bulletin or the Technical Hotline.
NEW FEATURES INTRODUCED WITH NAVIGATION SOFTWARE V27
Only E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with DVD Navigation system
Disclaimer screen disappears automatically after 8 second
City/Town names displayed in the map
E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with DVD Navigation system
E65/E66 (7 Series) DVD NAVI03 (from03/05)
Destination input when Country (UNITED STATES or CANADA) is selected via:

ZIP code
City name
Destination input when an US State or a Canadian Province is selected via:
Street name
City name
ZIP code
Note: Only in conjunction with NAVTEQ DVD road Map 2006-2
POI (Point of Interest) icons and "City Center" icons are displayed together
Travel Information (TMC) is no longer displayed (is inactive and not selectable)
Entries in "Address Book/Last Destination" displayed as:
City name, Street name (Destination entry via City name)
ZIP code, City name, Street name (Destination entry via ZIP code)
Product Information
Legal Disclaimer for usage of the Navigation system and the data on the NAVTEQ road maps
How to report missing or incorrect data feedback to NAVTEQ:
Website: http://www.navteq.com/bmwmaps
Phone: 1-888-navteq9 (628-8379)
Email: [email protected]
E83 (X3) and E85 (Z4) with flap display
Software fix for the flap issues (opening/closing)
FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V26
The actual location is shown as an arrow in a circle
The destination is marked with a checkered flag
Map Positioning in "Travel Direction" can now be selected in scales up to 100 mls
Disable POI icons is now selectable on I-Bus DVD NAV systems in:
General Destinations
Travel Information
The following functions are now selectable on E65/E66 with NAVI03 (from 03/2005):

Hide Map Icons
General Destinations and Travel Information
After loading NAV SW V27, the vehicle must be driven to ensure the proper function of the
Navigation system and the correct displaying (Interstate Icons)
CHECKING SOFTWARE VERSION
MK I Systems
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "1-1/80". The numbers have the following meanings: first digit 1 - is a 1st generation navigation
system (MK I); second digit 1 - is a 1st device variant (top navigation – MK Ic color screen); the last two digits
80 - are the software version of the graphic component (8.0).
MK II Systems
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "2-1/81". The numbers have the following meanings: first digit 2 - is a 2nd generation navigation
system (MK II); second digit 1 - is a 1st device variant (top navigation – MK IIc color screen); the last two digits
81 - are the software version of the graphic component (8.1).
MK III Systems
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "3-1/63" or "3-2/63"(MK III with split screen). The numbers have the following meanings: first
digit 3 - is a 3rd generation navigation system (MK III); second digit 1 - is a 1st device variant (top navigation –
MK IIIc color screen), or 2 – is a 2nd device variant (radio navigation – MK IIIm monochrome display); the last
two digits 63 - are the software version of the graphic component (6.3).
DVD navigation system for I-Bus vehicles
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "4-1/70". The numbers have the following meanings: first digit 4 - is a 4th generation navigation
system (DVD); second digit 1 - is a 1st device variant (top navigation – DVD color screen); the last two digits 70
- are the software version of the graphic component (7.0).
E65/E66 Systems
Enter the Service Mode of the Control Display
Select "MOST Devices"
Scroll down and select "Navigation"
Scroll down a few pages until "Software Version" is displayed
Software Version for CD navigation (NAVI01) should be 7.3.2 (I-level E065-05-03-810.2)
Software Version for DVD navigation (NAVI02) should be 8.4.4 (I-level E065-05-03-800.2)
Software Version for DVD navigation (NAVI03) should be 9.3.0C (I-level E065-06-03-500)
Current Software Versions

Software
version Application
8.0 MK I - E39/E38 (up to 9/97)
8.1 MK II - E39/E38 (from 9/97), E46, X5
9.0 MK II - Radio Navigation – E52 (Z8)
5.1 MK III Radio Navigation – E52 (Z8) from 09/00
3.1* MK III w/o Split Screen -E46 from 06/00, E39/E38 from 09/00, E53 from
10/00
6.3 MK III with Split Screen
7.0 MK IV DVD Navigation
7.3.2 E65/E66 NAVI01 (CD-drive)
8.4.4 E65/E66 NAVI02 (DVD-drive)
9.3.0C E65/E66 NAVI03 (DVD-drive)
*Included in Navigation software CD V17.1
LOADING SOFTWARE (ALL EXCEPT E65/E66)
For MK I, MK II, MK III, and DVD NAV systems (except E65/E66) use the following software loading
instructions:
Turn ignition to position 1 (terminal R). 1.
Do not cycle the key or perform diagnosis while installing the new software. Make sure that the power supply is
stable, i.e. do not switch on any electrical loads.
Activate "GPS-Navigation" and acknowledge the screen disclaimer by pushing the rotary knob. 2.
Remove the map CD from the Navigation computer by pressing "eject" button. 3.
Insert the Navigation Software CD (V17.1 P/N 01 59 9 789 299 index "x" for MK III without split
screen, V27 P/N 01 59 0 141 891 index "s" for all other versions).
4.
Mark I System (up to 9/97 production): 5.
After a few seconds, the BMW roundel will appear on the board monitor and will be "filled in" clockwise to
show the progress of loading (approx. 4-6 minutes).
Mark II System (from 9/97 production),
Mark III System (E46 from 06/00 and E38/E39/E52 from 09/00 production),
DVD navigation system (E46, E39, E52 from 09/02 and E53, E85 from 10/02 production):
After a few seconds, a menu of notes on loading procedure and "progress" bar appear on the board monitor.
When the loading process has been completed, the message "Software has been successfully loaded" is displayed.

Remove the operating software CD and confirm the end of the loading process by pressing the rotary
push-button on the board monitor. "OK" appears in the display.
6.
Drive the vehicle before delivering to the customer to ensure the correct function and displaying (Interstate
Icons) of the Navigation system.
7.
LOADING SOFTWARE (E65/E66 ONLY)
When programming any E65/E66 using Progman V21 or higher, you will be prompted by the Progman
screen that "BMW Navigation CD Version 27" must be loaded prior to programming the vehicle.
Note: Connect an approved battery charger before loading software.
Turn on ignition to Terminal R or 15 1.
Enter the Navigation Menu. 2.
Remove the NAVTEQ road map CD/DVD 3.
Insert the Navigation Operating Software CD V27 (P/N 01 59 0 141 891 index "s") into the
navigation computer and use Progman V21 or a more recent version for NAVI03 (DVD navigation).
4.
Select "Yes" with the Controller to install software. 5.
The software will then load in two steps, takes approximately 10-15 minutes. 6.
Do not touch the iDrive while the software is loading. 7.
When the installation is finished the CD will be ejected. The message "Installation Successful, Remove
Software loading CD and press OK" will appear. At this point select "OK" with the Controller.
8.
The Navigation system will then "reinitialize". 9.
When prompted, insert NAVTEQ road map CD/DVD. 10.
Refer to SI B09 05 01 (Coding, Individualization and Programming) for any necessary coding and
programming. Note that Progman will automatically reprogram all programmable control units that do not
have the latest software.
11.
Drive the vehicle before delivering to the customer to approve the correct function and displaying
(Interstate Icons) of the Navigation system.
12.
NAVIGATION COMPUTER REPLACEMENT MK III
When replacing a defective MK III computer, a configuration signal is required to allow the new computer
to load the correct software for its respective application. This is generated by using DIS coding program
"Coding ZCS C45.0" or higher and Navigation System operating software CD V 17.1 or V27.
Connect DIS/GT1 tester to vehicle 1.
From the DIS Coding/Programming select "1 ZCS Coding" 2.
Select appropriate engineering series (E38, E39, etc.) 3.
Select "4 conversion" 4.
Select "3 IKE/Kombi" 5.

Select "2 Language" 6.
At prompt "Is the CD-ROM present?" – select "Yes", but do not insert Navigation CD into the Nav
Computer yet!
7.
First select the main language and then an additional language (the choices are: English, French, Italian,
Spanish, German)
8.
NOTE: The announcer's voice gender (male or female) can't be selected anymore. 9.
MK I, MK II & MK III: Only male.
MK IV (DVD NAV), NAVI01, NAVI02 & NAVI03: Only female
After activation of the automatic coding, the DIS tester tells you to follow the instructions on the monitor
for Navigation CD installation
10.
Place the Navigation CD into the navigation computer CD drive 11.
Important: Do not switch ignition OFF during software loading procedure
Once loading has been completed, remove the CD and then confirm completion by pressing the rotary
push-button on the monitor
12.
Turn ignition OFF for 10 seconds, then turn it ON and conduct a functional check 13.
After this step has been finished, encode the Navigation computer in the regular manner using the path "1
Recoding"
14.
Troubleshooting Hints
The following problems may occur during the software loading procedure:
The message "CD defective" appears on the display screen.
The message "Fault during programming" appears on the display screen.
The message "The system is restarting" appears on the display screen.
The installation process has stopped and the display screen is blank and the power LED on the navigation
computer is off. The CD will not eject.
These complaints are usually the result of a faulty Navigation Operating software CD.
For points 1-3 for error messages that appear on the display screen, check for the correct software version
and try loading a new Navigation CD.
For a CD that will not eject from the Navigation computer follow the procedure below:
Remove the Navigation computer. 1.
Unplug the voltage supply (blue connector). 2.
Reconnect the voltage supply and immediately press the eject button repeatedly until the CD in the
drive is ejected.
3.

Insert a new Navigation CD and restart the installation process. 4.
PARTS INFORMATION
Part Number Description
01 59 9 789 299 Navigation Software CD V17.1 Index "x"
01 59 0 141 891 Navigation Software CD V27 Index "s"
Copies of the CD V27 will be shipped to every BMW Center through the Automatic Tool Shipment
Program.
WARRANTY INFORMATION
Updating the vehicle at customer request is not covered under warranty.
[ Copyright © 2006 BMW of North America, LLC ]

[320dM]

correndo o risco de ser chato, voltei a repetir todo o procedimento, cuidadosamente, e nada ! continua a dizer que o sistema está actualizado.
e não acredito que seja por ter o monitor 4.3...
caro jcarlos, como posso confirmar se a versão que estou a instalar é a mesma que a sua ?
obrigado.

[nsantos]

tenho o mk3 (versão CD).
Fiz ontem a actualização de software ... aparentemente tudo correu bem mas não me aparece a cena da prespectiva.
Ficou com a versão 3-1-63. Alguém me pode validar esta versão?

[320dM]

pois...
essa versão é a que faz o split screen, não faz a vista 3D, é a versão que eu tenho.
pelo que tenho andado a ler o 3D só dá mesmo para a versão MKIV DVD.
só mesmo trocar de CD MKIII para o DVD...
pois é...

[nsantos]

depois disso tb andei a pesquisar um bocado e foi o que calculei.
sempre deu para fazer a actualização de software, apesar de não encontrar diferenças nenhumas.

[Gualberto Rocha]

eu tinha a 3-1.43 passou para 3-1.63 sem problemas!

Pelo k me parece a unica diferença k notei foi na rapidez de processamento!! bastante mais rapido a aceitar funçoes e no gps!;)

[320dM]

por mais que actualizem a ultima versão para o mkIII é a 3-1.63

[pantorras]

estou a sacar agora...falta meia hora...
tenho um gps com telefone e tv 4:3. é o mk3
poderei meter o cd sem receio no carro?

....
fiz asneiras...a bosteira do cd passou-me para um software antigo! e o gps "desapareceu"! que fazer alguem sabe¿?

[pantorras]

encontrei um grande site! da um grande jeito
http://www.gren.ru/navi%20OS%20software.html

[JOFIMO]

jcarlos, diz-me uma coisa por favor, acabei de comprar no ebay.de um sistema de navegação de montar no sitio do cinzeiro e porta oculos com comando, por acaso sabes que versão será? eu penso que é MKIII pelo que apanhei no oem, no entanto, diz-me a tua opinião, já agora outra coisa, já consegui a EBA en espanhol, mas falta-me a EBA para ligação e montagem para o "módulo de comutação de telefone e navegação" por acaso não sabes quem tenha isso?
Um abraçoe obrigado

[320dM]

pantorras, isso é estranho, ele passar para uma versão mais antiga, mas de qualquer modo, basta actualizares com uma versão recente, de preferencia a 27 e fica outra vez nos trinques
cumps.

ps. se o sistema der algum erro não insistas e diz alguma coisa.

[topa]

Já anda aí uma versão 27.1 mas só interessa mesmo a quem tenha sistema de navegação já com DVD Mk4...

Abraços